Bertazzoni MAST365INSXT Manual download pdf (Page 9)

/ Induction cooktop

INDUCTION COOKTOP

COOKING WITH INDUCTION

Underneath each cooking zone there is a coil cal-

led an inductor. The inductor generates a variable

magnetic ﬁ eld using electric power. When a pan is

placed inside this magnetic ﬁ eld, the highfrequen-

cy current radiates directly on the bottom of the

pan and produce the heat needed to cook.

After use the display can show the symbol ‘H’ if

there is residual heat. The symbol ‘H’ go out when

the temperature drops to below about 140°F/60°

TURNING ON THE INDUCTION ELEMENT

The symbol above each knob indicates which ele-

ment that knob controls.

The operation power is regulated through the

knob and is shown by a display on the cooktop

surface.

To turn on the heating zone, press in the control

knob (Fig.14A-14B) and turn it clockwise. Settings

range from a minimum of 1 to a maximum of 9.

USING SPECIAL FUNCTIONS

A - Heating Accelerator mode.

The Heating Accelerator mode allows each zone

to be operated at peak power for a time proportio-

nal to the heating power selected.

• Turn the knob anti-clockwise, select setting “A”

and then release. The letter “A” will appear on

the display on the cooktop area

• After 3 seconds, you may select the heating

setting of your choice. Once a setting between

1 and 9 has been selected, “A” and the chosen

setting will ﬂ ashin sequence on the display.

While the heating accelerator is in operation, the

heating level can be increased at any time. The

“full power” time will be modiﬁ ed accordingly. If the

power is reduced by turning the knob anticlockwi-

se, option “A” is automatically deactivated.

P - Power Mode.

The power mode allows the user to operate each

heating zone continuously at the maximum power

for a time of no more than 10 minutes. This mode

can be used to bring a large amount of water to

the boil in a hurry, or to turn up the heat under

meat.

• Turn the knob clockwise and set heating level

to 9, then use the knob to set the “P” position

and release it.

• The symbol “P” will appear on the correspon-

ding zone display.

• After 10 minutes, the power will be reduced au-

tomatically to 9 and the “P” will disappear.

The power mode can be turned oﬀ at any time

by reducing the heating level. If a pan is removed

from the cooking zone while the power function is

on, the function is switched oﬀ .

- Holding Mode.

The holding mode keeps the temperature of the

bottoms of pans at about 160°F/70°C . This allows

foods to be heated gently and kept hot with opti-

mal energy consumption. Holding mode can be

kept in operation for up to 2 hours.

The holding mode is and is indicated by the

relevant symbol on the cooking zones.

∏ - Bridge Mode.

The bridge mode allows to use the 2 right-side

cooking zones as a single cooking zone. Power

Mode is not allowed when the zones are operated

in Bridge mode.

• Rotate both knobs, rear right and front right, at

the same time in the P position and keep the

knobs in that position.

• The ∏ symbol will blink in the display, then re-

turn to the power level.

• To control the bridge power level, use the knob

4 (front right zone). If you turn knob 3 (rear right

zone) the display shows a horizontal segment

and the bridge function ends.

OFF

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 23 24

Comments to this Manuals

No comments

Bertazzoni MAST365INSXT Manual Page 9

Comments to this Manuals

Related products and manuals for Ovens Bertazzoni MAST365INSXT