Bertazzoni KIN30PROX User Manual download pdf (Page 9)

ENGLISH

ELECTRICAL CONNECTION

(Intended only for qualied personnel)

Disconnect the equipment from electrical mains power supply before carry-

ing out any operations on the hood.

Ensure that the wires inside the hood are not disconnected or cut:

in the event of damage, contact your nearest Servicing Department.

Refer to qualied personnel for electrical connections.

Connection must be carried out in compliance with the provisions of law in force.

Before connecting the hood to the electrical mains power supply, check that:

 

hood;

 -

cations located inside the hood);

 -

ing 158°F (70 °C);

 

with regulations in force;



the socket used to connect the hood is within reach.

In case of:

 

The wires must be connected as follows: yellow-green for grounding, blue for neutral

and brown for the live. The plug must be connected to an adequate safety socket.



ﬁxed equipment not provided with a power supply cable and plug, or any other device

that ensures disconnection from the electrical mains, with an opening gap of the con-

tacts that enables total disconnection in overvoltage category III conditions.

Said disconnection devices must be provided in the mains power supply in compliance

with installation regulations.

The cable must not be cut oﬀ by the switch.

The Manufacturer declines all responsibility for failure to comply with the safety regulations.

FUMES DISCHARGE

EXTERNAL EXHAUST HOOD SUCTION

In this version the fumes and vapours are discharged outside through

the exhaust pipe.

To this end, the hood outlet ﬁtting must be connected via a pipe, to an

external output.

The outlet pipe must have:

 

 

ﬂowing back into the motor.

 

 

the hood.

You are required to insulate the pipes if it passes through cold environments.

In the presence of motors with 800m

/h or higher, a check valve is present to prevent

external air ﬂowing back.

HOOD WITH INTERNAL RECIRCULATION FILTERING

In this model, the air passes through the charcoal ﬁlters to be puriﬁed

and recycled in the environment.

Ensure that the active carbon ﬁlters are assembled into the hood, if not,

install them as indicated in the assembly instructions.

In this version the check valve must not be assembled: remove it if it is on the air

outlet ﬁtting of the motor.

ASSEMBLY INSTRUCTIONS

Intended only for qualied personnel

The hood can be installed in various congurations.

The generic assembly steps apply to all installations; for each case, follow

the specic steps provided for the required installation.

OPERATION

WHEN TO TURN ON THE HOOD?

Switch on the hood at least one minute before starting to cook to direct fumes and vapours

towards the suction surface.

After cooking, leave the hood operating until complete extraction of all vapours and odours.

By means of the Timer function, it is possible to set auto switch-oﬀ function which will allow

the hood to turn oﬀ automatically after 15 minutes of operation.

WHICH SPEED IS TO BE SELECTED?

1st speed: maintains the circulation of clean air with low electricity consumption.

2nd speed: normal conditions of use.

3rd speed: presence of strong odours and vapours.

4th speed: rapid disposal of odours and vapours.

WHEN SHOULD THE FILTERS BE WASHED OR REPLACED?

The metal ﬁlters must be cleaned every 30 hours of operation.

The active carbon ﬁlters must be replaced every 3-4 months, depending on the use of the

hood.

For further details refer to the “MAINTENANCE” section.

ELECTRONIC PUSHBUTTON PANEL

Motor ON/OFF

Upon start-up, the speed is that stored at the previous operation.

Increase speed from 1 to 4

Speed 4 is only active for a few min-

utes, then speed 3 activates.

The speeds are indicated by the LEDs

on the keys:

Speed 1

Speed 2

Speed 3

Speed 4

("+" LED ﬂashing)

Reduce speed from 4 to 1

Light on/o

TIMER (red LED ﬂashing)

Auto switch-oﬀ after 15 min.

The function deactivates (red LED oﬀ) if:

- The TIMER key (

) is pressed again.

- The ON/OFF key (

) is pressed.

FILTER ALARM (red LED steady on with ( ) oﬀ)

Anti-grease ﬁlter maintenance after approximately 30 hours of operation.

Press (

) the meter for 3 seconds to reset.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 19 20

Comments to this Manuals

No comments

Bertazzoni KIN30PROX User Manual Page 9

Comments to this Manuals

Related products and manuals for Unknown Bertazzoni KIN30PROX