Bertazzoni H366GGVVI Installation Manual

Installation, Service and User Instructions FREESTANDING GAS RANGES BERTAZZONI DIMENSIONS: 36’’ (911 mm)(W) x 25 1/8’’ (640 mm)(D) x36’’ (911 mm)(H

10 Wiring diagram For freestanding gas range model H366GGV M3Y0GTV4(L,N,D)(2 or 5)A CAUTION: label all wires prior to disconnection when servici

11GAS CONNECTION All gas connections must be made according to national and local codes. The gas supply (service) line must be the same size or great

12PERFORMANCE CHECKLlST All burners are tested before leaving the factory. There are no adjustments for the burners if connected according to the inf

13 - CHANGING THE NOZZLES FOR USE WITH OTHER TYPES OF GAS: To change the nozzles of the burners use the following procedure: Lift up the burne

14 Models H366GGV [M3Y0GTV4(L,N,D)(2 or 5)A] Adapting to different types of gas Burner Position Injector Gas Pressure Max Rate Min Rate

15Work surface burner adjustment: follow the instructions below to adjust the work surface burner minimum: 1) Light the burner and set the knob to th

16USER MANUAL WARNINGS: Do not to cover the holes inside the oven with aluminium paper Do not to cover the burners of cooktop with aluminium paper

17CONTROL PANEL DESCRIPTION On the control panel, small symbols show the function of each knob or key. Here as follows are the several controls that

18 WARNING: check the position of the burner caps before operation. Correct usage of pans: - Dry the bottom of the pan before placing it on the ho

19The oven burner can be ignited in different ways: - Manual lighting (it is always possible even when the power is cut off): To light the oven, ope

2IMPORTANT - PLEASE READ AND FOLLOW -Before beginning installation, please read these instructions completely and carefully. -Do not remove permanent

20To activate the convection fan use the selector placed on control panel. CONVECTION GAS OVEN COOKING TABLE TEMP °F/ °C HEIGHT MINUTES MEAT

21 USING THE GAS BROILER The gas broiler is controlled with the same gas oven knob, but turning it clockwise instead of counterclockwise (see the ga

22 CLEANING THE APPLIANCE: Never use abrasive cleaners Before cleaning the appliance it should be disconnected from the power supply. Cleaning the wo

SPARE PARTS LISTH366GGVNEH366GGVCRH366GGVVINUMBER COMPONENT DESCRIPTION11 202387 BURNERS FLASK 2 2 218 202432 PART FOR DUAL WOK AND SEMI RAPID BURNE

917 108665 SIDE BEIGE 2917 108666 SIDE BORDEAUX 2929 202389 RIGHT VERTICAL VENT 1 1 1930 202214 FEET SUPPORT 2 2 2940 201168 FIXING FOR WORK TABLE 2 2

3WARNING Read this instruction booklet before installing and using the appliance. The manufacturer will not be responsible for any damage to property

4ATTENTION: A manual valve shall be installed in an accessible location in the gas line external to the appliance for the purpose of turning on or sh

5INSTALLATION MANUAL ANTI-TIP STABILlTY DEVICE INSTALLATION INSTRUCTIONS 1. The anti-tip bracket have to be installed to the rear wall as shown. Th

6BACKGUARD INSTALLATION INSTRUCTION It’s always compulsory to installa the riser even for an island installation 1) Remove n°2 screws fixing worktop

7WORKTOP FRONT HANDLE INSTALLATION INSTRUCTIONS In order to increase the clearance between front edge of the worktop and the burners for your safety

8 INSTALLATION SIDE-BY-SIDE TO KITCHEN CABINET 1. This range may be installed directly adjacent to existing 36" (91.5 cm) high cabinets. IMPORT

9COOKER HOOD INSTALLATION The bottom of the hood should be 25 1/2" (65 cm) min. to 31 1/2" (80 cm) above the countertop. This would typica